tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm

You can fill out the integrated inquiry form below on this detail page to share your company profile. Our consultancy desk will review your query regarding parameters and guide you on how to coordinate efficiently with the procurement team of Employees state insurance corporation ESIC

Tender18 provides end-to-end professional bidding support and documentation advisory for tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm . Our senior analysts help you decode the complete project guidelines, manage accurate costing sheets, and complete error-free submissions on the official platform used by Employees state insurance corporation ESIC.

Most online bids face rejection during the initial evaluation round due to avoidable errors like uploading blurred document scans, submitting expired DSCs, or missing critical experience papers required for tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm in Assam.

Eligibility for outstation bidders depends entirely on the terms set inside the document for tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm. While many public sector projects allow national competitive bidding, certain localized works require local offices or specific registration metrics in Kamrup.

If this procurement is routed through the central marketplace, an active GeM Seller ID is mandatory to supply items. Tender18 offers complete assistance for brand cataloging, profile creation, and vendor assessment required officially by Employees state insurance corporation ESIC

To register an eligible bid for these contracts, companies must prepare their core compliance documents. Vendors operating across Assam must ensure they possess a valid GST registration, permanent account number (PAN), and active Class-3 Digital Signature Certificates.

This public procurement cycle is specifically looking for qualified vendors and suppliers who can provide high-quality solutions. The operational execution, delivery, and deployment of these materials must be managed locally within the Kamrup region.

The estimated project cost and budget thresholds can be reviewed directly inside the tender document. Bidders can analyze these qualification files to check if their firm meets the financial capability criteria specified for tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm by Employees state insurance corporation ESIC

You can download the commercial Bill of Quantities (BOQ) spreadsheet directly using the secure link provided on this page. The BOQ file contains the item descriptions and rate filling forms officially validated for tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm within the Assam jurisdiction

The official timeline and deadline details for tender for odu 1 , odu 2 , 4-way cassette unit 1 , 4-way cassette unit 2 , y joints 1 , y joints 2 , cu piping , damper , actuator , nitrile rubber , wiring , mccb , mcb db 1 , mcb db 2 , mcb , allied electrical works , dx coil unit , 4-way cassette unit 3 , ahu , ahu kit , ref gas , control cable , drain pipe , ducting , acoustic nitrile rubber , vfd , strip heater , pdp , al cable 1 , al cable 2, supply installation testing and commissioning of vrf based air conditioning system, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 14 hp, supply and itc of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin rotary/scroll compressor(s), minimum two compressors (with individual seperate pcb) for above 6 hp modules/non module, microprocessor based controller, top discharge type condensing unit(s), with r-410-a refrigerant or equivalent, vibration isolators with suitable foundation etc. complete as required, as per nit specifications - 10 hp, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.56 tr, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 2.0 tr, supplying, installation, testing and commissioning of odu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, supplying, installation, testing and commissioning of idu y/t/multi joints. joints shall be of same original equipment manufacturer (oem) make as of odus and idus, refrigerant piping for vrf system - supply , installation , testing and commissioning of copper piping in brazed construciton, complete with nitrile rubber insulation, supports/suspenders, as per enclosed specifications. refrigerant piping for suction gas with 19mm thick nitrile insulation & refrigerant piping for liquid gas with 13mm thick nitrile insulation (various capacities as per boq of nit document, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - damper, supply, installation, testing and commissioning of motorized (on-off type) duct mounted gi volume control damper with enthalpy sensor and necessary control wire for integration within ahu room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to smacna/is and as per specifications complete etc. as required - actuator, supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell nitrile rubber (class-o) insulation on existing duct as per nit specifications - 25mm, wiring for circuit/ submain wiring along with earth wire as per nit specifications, providing and fixing following rating and breaking capacity and pole mccb with thermomagnetic release and terminal spreaders in existing cubicle panel board as per nit specifications, supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing following way, tpn, sheet steel, mcb distribution board, 240 v, on surface/ recess as per nit specifications, supplying and fixing 5 a to 32 a rating, 240/415 v, 10 ka mcbs as per boq enclosed with nit document, allied electrical works as per as per boq enclosed with nit document including supply installation testing and commissioning of panels, supply, installation, testing and commissioning of approved make direct expansion (dx) type cooling coil unit for air handling unit (ahu) as per boq/ specifications enclosed with nit document, supply and itc of following minimum capacity 4 way cassette type indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan / dynamically balanced blower, multispeed motor, coil section with dx copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless remote control etc as per nit specifications - 3.2 tr, supply and itc of sheet metal sectionalised construction double skin ahu for vrf/vrv system as per boq/ specifications enclosed with nit document, supply and itc of ahu kit, refrigerent gas - supply and top-up of refrigerent gas r410a., control cable - supply, installation, testing & commissioining of control cum transmission cabling between odu & idu 2c x 1.0 sqmm cu cable in rigid pvc conduit duly supported., drain piping - supply, installation and commissioning of upvc drain piping with 6/9 mm thick closed cell nitrile rubber insulation with all fittings, solvent, necessary accessories and supports. thermal insulation sleeve joints shall be sealed with black tape - 25 mm/32 mm, supply, installation, balancing and commissioning of factory/hand fabricated aluminium sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required - thickness 0.8 mm, supplying and fixing of following thickness open cell acoustic nitrile rubber insulation on existing duct after applying suitable adhesive for nitrile rubber. as per specifications and as required - thickness 10mm., supply, installation,testing, & commissioning of variable friquency drive, supply,installation,testing & commissioning of strip heater along with controller, supply of power distribution panel ac distribution panel board - ip65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, without mcbs etc. as required to be made of customised requirment for outdoor fixing., supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 16 sqmm, supply of lt armoured aluminium cable (1.1kv) as per boq/ specifications enclosed with the nit document - 35 sqmm are available inside the detailed notification files. Bidders planning to target this contract in Kamrup should check the official portal schedule early to complete their online technical and financial submission well before the closing hours.